Connection to TTN With OTAA

Hi Adam,
Sorry if this comes a bit late. Was finalizing the V2 while this question came in. In the midst of writing a tutorial for this.
But, here are the important points that get the example provided by Matthijs Kooijman’s LMIC library running correctly:

• Both the Device EUI and Application EUI (both are the 8-bytes key) are displayed as MSB….LSB on the TTN dashboard. But, you must key in as LSB…MSB on the OTAA example.
• Add LMIC_setClockError(MAX_CLOCK_ERROR * 1 / 100); after LMIC_reset();
• Add #define Serial SerialUSB if you want to see the debug messages on the USB port.

These are only 3 changes needed to get going.

Some stuff I’ll be adding in the tutorial includes using the EUI64 identification and using the RTC to resides in low power mode while connected to the network. This will serve as a good skeleton firmware for low power application using OTAA to TTN.

• This reply was modified 7 years, 5 months ago by LIM PHANG MOH.

I am following your instructions trying to connect my Mini Ultra Pro V2 to TTN using Matthijs’ LCIM library. However, I am stuck at joining the TTN network.

I’ve changed Matthijs’ ttn-otaa example in the following ways:
– Added APPEUI from my TTN application page (made sure to reverse it)
– Added DEVEUI from my TTN application page (made sure to reverse it)
– Added APPKEY from my TTN application page (as is – i.e. not reversed)
– Changed lmic_pins per your instructions above.
– Added LMIC_setClockError(MAX_CLOCK_ERROR * 1 / 100); after LMIC_reset();
– Added #define Serial SerialUSB for serial monitor output
– Added while(!Serial); after Serial.begin(9600); (otherwise I get not output in the serial monitor)

In the serial monitor I receive the following message and nothing more:

Starting
Packet queued
321993: EV_JOINING

Even if I leave it for minutes nothing happens. I am around 200 meters away from the nearest TTN access point, so I’m thinking rangewise I should be good (although this is my first experience with LoRa and/or TTN).

Any suggestions as to what I can try to get it working?

Hi Matthias,

Check your TTN 8-byte DEV EUI. Mine didn’t connect until that gets corrected and same as on the device on OTAA join. Take note of it’s MSB-LSB sequence too. In fact, OTAA is easier (less things to make mistake on the dashboard except the above).

Hi Matthias,
I’m sorry but I should have put this up some time ago. My plan was to include the sleeping portion for a tutorial/guide before posting it up but it seems that I have to do it before this particular issue is solve. When it starts, the code prints out the 64-bit MAC address. Key those in as it is on the TTN dashboard.

/*******************************************************************************
   Copyright (c) 2015 Thomas Telkamp and Matthijs Kooijman

   Permission is hereby granted, free of charge, to anyone
   obtaining a copy of this document and accompanying files,
   to do whatever they want with them without any restriction,
   including, but not limited to, copying, modification and redistribution.
   NO WARRANTY OF ANY KIND IS PROVIDED.

   This example sends a valid LoRaWAN packet with payload "Hello,
   world!", using frequency and encryption settings matching those of
   the The Things Network.

   This uses OTAA (Over-the-air activation), where where a DevEUI and
   application key is configured, which are used in an over-the-air
   activation procedure where a DevAddr and session keys are
   assigned/generated for use with all further communication.

   Note: LoRaWAN per sub-band duty-cycle limitation is enforced (1% in
   g1, 0.1% in g2), but not the TTN fair usage policy (which is probably
   violated by this sketch when left running for longer)!

   To use this sketch, first register your application and device with
   the things network, to set or generate an AppEUI, DevEUI and AppKey.
   Multiple devices can use the same AppEUI, but each device has its own
   DevEUI and AppKey.

   Do not forget to define the radio type correctly in config.h.

 *******************************************************************************/

#include <lmic.h>
#include <hal/hal.h>
#include <SPI.h>
#include <Wire.h>       
#define EUI64_CHIP_ADDRESS 0x50
#define EUI64_MAC_ADDRESS 0xF8
#define EUI64_MAC_LENGTH 0x08
#define Serial SerialUSB

// This EUI must be in little-endian format, so least-significant-byte
// first. When copying an EUI from ttnctl output, this means to reverse
// the bytes. For TTN issued EUIs the last bytes should be 0xD5, 0xB3,
// 0x70.
static const u1_t PROGMEM APPEUI[8] = { 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 };
void os_getArtEui (u1_t* buf) {
  memcpy_P(buf, APPEUI, 8);
}

// This should also be in little endian format, see above.
u1_t DEVEUI[EUI64_MAC_LENGTH];
void os_getDevEui (u1_t* buf) {
  memcpy(buf, DEVEUI, EUI64_MAC_LENGTH);
}

// This key should be in big endian format (or, since it is not really a
// number but a block of memory, endianness does not really apply). In
// practice, a key taken from ttnctl can be copied as-is.
// The key shown here is the semtech default key.
static const u1_t PROGMEM APPKEY[16] = { 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 };
void os_getDevKey (u1_t* buf) {
  memcpy_P(buf, APPKEY, 16);
}

static uint8_t mydata[] = "Hello, world!";
static osjob_t sendjob;

// Schedule TX every this many seconds (might become longer due to duty
// cycle limitations).
const unsigned TX_INTERVAL = 60;

// Pin mapping
const lmic_pinmap lmic_pins = {
  .nss = 5,
  .rxtx = LMIC_UNUSED_PIN,
  .rst = 3,
  .dio = {2, 6, 7},
};

void onEvent (ev_t ev) {
  Serial.print(os_getTime());
  Serial.print(": ");
  switch (ev) {
    case EV_SCAN_TIMEOUT:
      Serial.println(F("EV_SCAN_TIMEOUT"));
      break;
    case EV_BEACON_FOUND:
      Serial.println(F("EV_BEACON_FOUND"));
      break;
    case EV_BEACON_MISSED:
      Serial.println(F("EV_BEACON_MISSED"));
      break;
    case EV_BEACON_TRACKED:
      Serial.println(F("EV_BEACON_TRACKED"));
      break;
    case EV_JOINING:
      Serial.println(F("EV_JOINING"));
      break;
    case EV_JOINED:
      Serial.println(F("EV_JOINED"));

      // Disable link check validation (automatically enabled
      // during join, but not supported by TTN at this time).
      LMIC_setLinkCheckMode(0);
      break;
    case EV_RFU1:
      Serial.println(F("EV_RFU1"));
      break;
    case EV_JOIN_FAILED:
      Serial.println(F("EV_JOIN_FAILED"));
      break;
    case EV_REJOIN_FAILED:
      Serial.println(F("EV_REJOIN_FAILED"));
      break;
      break;
    case EV_TXCOMPLETE:
      Serial.println(F("EV_TXCOMPLETE (includes waiting for RX windows)"));
      if (LMIC.txrxFlags & TXRX_ACK)
        Serial.println(F("Received ack"));
      if (LMIC.dataLen) {
        Serial.println(F("Received "));
        Serial.println(LMIC.dataLen);
        Serial.println(F(" bytes of payload"));
      }
      // Schedule next transmission
      os_setTimedCallback(&sendjob, os_getTime() + sec2osticks(TX_INTERVAL), do_send);
      break;
    case EV_LOST_TSYNC:
      Serial.println(F("EV_LOST_TSYNC"));
      break;
    case EV_RESET:
      Serial.println(F("EV_RESET"));
      break;
    case EV_RXCOMPLETE:
      // data received in ping slot
      Serial.println(F("EV_RXCOMPLETE"));
      break;
    case EV_LINK_DEAD:
      Serial.println(F("EV_LINK_DEAD"));
      break;
    case EV_LINK_ALIVE:
      Serial.println(F("EV_LINK_ALIVE"));
      break;
    default:
      Serial.println(F("Unknown event"));
      break;
  }
}

void do_send(osjob_t* j) {
  digitalWrite(13, HIGH);
  
  // Check if there is not a current TX/RX job running
  if (LMIC.opmode & OP_TXRXPEND) {
    Serial.println(F("OP_TXRXPEND, not sending"));
  } else {
    // Prepare upstream data transmission at the next possible time.
    LMIC_setTxData2(1, mydata, sizeof(mydata) - 1, 0);
    Serial.println(F("Packet queued"));
  }
  // Next TX is scheduled after TX_COMPLETE event.
  
  digitalWrite(13, LOW);
}

void setDevEui(unsigned char* buf)
{
  Wire.begin();
  Wire.beginTransmission(EUI64_CHIP_ADDRESS);
  Wire.write(EUI64_MAC_ADDRESS);
  Wire.endTransmission();
  Wire.requestFrom(EUI64_CHIP_ADDRESS, EUI64_MAC_LENGTH);
   
  // Format needs to be little endian (LSB...MSB)
  while (Wire.available())
  {
    *buf-- = Wire.read();
  }
}

void setup() {
  unsigned char count;
  
  pinMode(4, OUTPUT);
  digitalWrite(4, HIGH);
  pinMode(13, OUTPUT);
  setDevEui(&DEVEUI[EUI64_MAC_LENGTH - 1]);
  while (!Serial) {};
  Serial.begin(115200);
  Serial.println(F("Starting"));
  Serial.print(F("DEVEUI: "));
  
  for (count = 0; count < EUI64_MAC_LENGTH; count++)
  {
    Serial.print("0x");
    if (DEVEUI[count] <= 0x0F) Serial.print("0");
    Serial.print(DEVEUI[count], HEX);
    Serial.print(" ");    
  }
  Serial.println();

#ifdef VCC_ENABLE
  // For Pinoccio Scout boards
  pinMode(VCC_ENABLE, OUTPUT);
  digitalWrite(VCC_ENABLE, HIGH);
  delay(1000);
#endif

  // LMIC init
  os_init();
  // Reset the MAC state. Session and pending data transfers will be discarded.
  LMIC_reset();
  LMIC_setClockError(MAX_CLOCK_ERROR * 1 / 100);

  // Start job (sending automatically starts OTAA too)
  do_send(&sendjob);
}

void loop() {
  os_runloop_once();
}

Thanks for the link! It helped me getting both of mine working now 🙂

A quick question – do I actually need to read out the Device ID of the Mini Ultra Pro and inserting it into the TTN dashboard?
I mean, couldn’t I make up my own Device ID (or let TTN generate one) and insert that Device ID into the LCIM code that I upload to the Ultra Pro Mini? Or is the actual hardware Device ID necessary (if so, why)?

Thanks for the reply!

Helps me getting better grip on LoRa 🙂